Materials Performance

NOV 2014

Materials Performance is the world's most widely circulated magazine dedicated to corrosion prevention and control. MP provides information about the latest corrosion control technologies and practical applications for every industry and environment.

Issue link:

Contents of this Issue


Page 90 of 92

88 NOVEMBER 2014 MATERIALS PERFORMANCE NACE INTERNATIONAL: VOL. 53, NO. 11 CORROSION BASICS Understanding the basic principles and causes of corrosion C oncrete is one of the most difficult surfaces to coat, due mainly to its wide range of properties. Steel is fairly uniform in texture, and workers are familiar with the proper ways to prepare and coat it. In contrast, concrete is quite porous and uneven in texture, with differences in density from one square inch to the next. Why Coat Concrete? Aesthetics Concrete is one of the most commonly used structural materials for private and public buildings. Because its natural color of dull, light to medium gray is often considered unattractive or, at best, uninspiring, more colorful coatings are often an architectural preference. Porosity The porosity of concrete allows moisture to penetrate it quite readily. Besides the problem of moisture intru- sion, chloride penetration can attack the steel bars and mesh that are typically used for structural reinforcement. Since the corrosion products tend to occupy greater volume than the original steel, expansive stresses can crack or spall concrete, which has poor cohesive strength compared to its compressive strength. In northern climates, this porosity often leads to destruction of the concrete structure during freeze-thaw cycles. Decontamination The normal porosity of concrete allows it to absorb almost any contaminant that comes into contact with it. Within nuclear facilities, coatings for concrete must be easily decontaminated in case of radia- tion spills. Within schools and hospitals, coatings must render the concrete surface coating chosen must not only be able to withstand the environment that comes into contact with the concrete, but it must also be able to penetrate and bond with the alkaline surface of the concrete. Oil-based or alkyd coatings are unsuit- able because the alkali in the concrete will react with the natural or synthetic oils in the coating, causing the creation of a soap-like film (saponification) that leads to delamination of the coating from the concrete. Curing Mechanism Regardless of the mix involved, or the additives in the mix, concrete cures by a process of hydrolyzing water with the ingredients in the mix. The commonly used rule of thumb is that concrete needs 28 days to cure at an average temperature of 20 °C (75 °F). It should be recognized that this traditional 28-day cure cycle allows the concrete to achieve the compressive strength designed into the mix ratio that was selected for the specific service conditions. Many coatings can be applied satisfactorily before the cure cycle is completed; however, this must be done in accordance with the manufacturer's recommendations. ACI 308, "Guide to Curing Concrete," provides recommenda- tions on temperature, moisture conditions, and time of cure for various concrete structures. This article is adapted by MP Technical Editor Norm Moriber from The Protective Coating User's Handbook, Second Edition, Louis D. Vincent (Houston, TX: NACE International, 2010), pp. 163-165. This book is avail- able from NACE as Item no. 37593. resistant to bacteria. Within food estab- lishments, coatings must resist growth of algae or other slime-type growths that could contaminate the food being processed. Conductivity Hospital operating rooms, solvent storage facilities, and microchip manufac- turing facilities are among the many areas where conductive fillers have to be used in conjunction with organic polymers to dissipate static electricity. Chemical Resistance Petrochemical plants contain millions of square feet of concrete surfaces. In areas where aggressive acids are being processed, the alkalinity of the concrete must be preserved by isolation from these acids with chemically resistant mortars, bricks, tiles, or sheet membranes. Properties of Concrete and Coatings Before one can successfully coat a concrete structure, it is necessary to understand and overcome the natural properties of concrete. Concrete can be a simple mixture of Portland cement, lime, aggregate, and water, but it can also contain fillers selected for specific structural properties and resins selected for specific chemical-resistant proper- ties, along with various additives selected to add specific strengthening properties to the otherwise simple mixture. Each variation creates a different surface with properties that can add or detract from a coating system's ability to bond with the concrete. Alkalinity First and foremost, concrete is naturally alkaline, both in its curing stages and after its final cure. Therefore, any Coating Concrete

Articles in this issue

Archives of this issue

view archives of Materials Performance - NOV 2014